<Huawei>sys //進入特權模式

[SW1]sys SW1 //設備命名SW1

[sw1]vlan batch 10 20 100 200 //批量創建vlan

[sw1]int g0/0/1 // 進入接口g0/0/1

[sw1-GigabitEthernet0/0/1]port link-type trunk //設置接口狀态為trunk

[sw1-GigabitEthernet0/0/1]port trunk allow-pass vlan all //允許通過的vlan

[sw1-GigabitEthernet0/0/1]int g0/0/2

[sw1-GigabitEthernet0/0/2]port link-type trunk

[sw1-GigabitEthernet0/0/2]port trunk allow-pass vlan all

[sw1-GigabitEthernet0/0/2]int g0/0/3

[sw1-GigabitEthernet0/0/3]po l t

[sw1-GigabitEthernet0/0/3]po t al vlan all

[sw1-GigabitEthernet0/0/3]int g0/0/4

[sw1-GigabitEthernet0/0/4]po l t

[sw1-GigabitEthernet0/0/4]po t al vlan all

[sw1]stp enable //開啟stp生成樹，默認開啟（紅色部分可省略）

[sw1]stp mode stp

sw1] dhcp enable //開啟dhcp enable，默認關閉，好久沒做都忘了

[sw1]ip pool dhcp10 //創建dhcp10為名字的地址池，

[sw1-ip-pool-dhcp10]gateway-list 192.168.10.254 //設置為網關

[sw1-ip-pool-dhcp10]network 192.168.10.0 m 24 //設置網段範圍及掩碼 m=mask(掩碼)

[sw1]ip pool dhcp20 //跟上面的一樣

[sw1-ip-pool-dhcp20]gateway-list 192.168.20.254

[sw1-ip-pool-dhcp20]network 192.168.20.0 m 24

[sw1-ip-pool-dhcp20]ip pool dhcp100

[sw1-ip-pool-dhcp100]gateway-list 192.168.100.254

[sw1-ip-pool-dhcp100]network 192.168.100.0 m 24

[sw1-ip-pool-dhcp100]ip pool dhcp200

[sw1-ip-pool-dhcp200]gateway-list 192.168.200.254

[sw1-ip-pool-dhcp200]network 192.168.200.0 m 24

[sw1-ip-pool-dhcp200]int vlan 10 //進入三層vlan接口

[sw1-Vlanif10]dhcp select global //分配方式為全局分配

[sw1-Vlanif10]ip add 192.168.10.254 24 //網關地址

[sw1-Vlanif10]dhcp select global

[sw1-Vlanif10]dis this //看這個模式下配置那些命令

ip address 192.168.10.254 255.255.255.0

dhcp select global

[sw1-Vlanif10]int vlan 20

[sw1-Vlanif20]dhcp select global

[sw1-Vlanif20]ip add 192.168.20.254 24

[sw1-Vlanif20]int vlan 100

[sw1-Vlanif100]ip add 192.168.100.254 24

[sw1-Vlanif100]dhcp select global

[sw1-Vlanif100]int vlan 200

[sw1-Vlanif200]ip add 192.168.200.254 24

[sw1-Vlanif200]dhcp selec global

<sw1>sa //保存

Are you sure to continue?[Y/N]y //Y=yes

<Huawei>sys

[Huawei]sys SW2

[SW2]undo in en //關閉提示，不然會很煩人

Info: Information center is disabled.

[SW2]sys SW2

[SW2]vlan batch 10 20

[SW2]int g0/0/1

[SW2-GigabitEthernet0/0/1]port link-type trunk

[SW2-GigabitEthernet0/0/1]port trunk al vlan all

[SW2-GigabitEthernet0/0/1]int e0/0/1

[SW2-Ethernet0/0/1]port link-type access

[SW2-Ethernet0/0/1]po de vlan 10

[SW2-Ethernet0/0/1]int e0/0/2

[SW2-Ethernet0/0/2]po l a

[SW2-Ethernet0/0/2]po de vlan 20

<SW2>sa

Are you sure to continue?[Y/N]y

[Huawei]sys

[Huawei]sysname sw4

[sw4]vlan b 100 200

Info: This operation may take a few seconds. Please wait for a moment...done.

[sw4]int g0/0/1

[sw4-GigabitEthernet0/0/1]po l t

[sw4-GigabitEthernet0/0/1]po t al vlan all

[sw4-GigabitEthernet0/0/1]int e0/0/1

[sw4-Ethernet0/0/1]po l a

[sw4-Ethernet0/0/1]po de vlan 100

[sw4-Ethernet0/0/1]int e0/0/2

[sw4-Ethernet0/0/2]po l a

[sw4-Ethernet0/0/2]po de vlan 200

[sw4]stp enable 可不輸入紅色的命令，默認開啟

[sw4]stp mode stp

Info: This operation may take a few seconds. Please wait for a moment...done.

<sw4>sa

The current configuration will be written to the device.

Are you sure to continue?[Y/N]y

SW4跟SW5命令相同

更多精彩资讯请关注tft每日頭條，我们将持续为您更新最新资讯!